Posts Tagged ‘school bags’
My kids started school last Thursday. I started sewing school bags for them on Wednesday and optimistically thought I might be able to finish their bags that day. But I didn’t. It took me until Sunday to get them finished. And it wasn’t because they were hard… they weren’t. In fact they were really fun and easy to make.
It was the design that had me stumped. Emma wanted an owl on her bag. Lily wanted first a butterfly, then a hedgehog and finally a squirrel. Lily’s fabric (above) had a lot going on, so the design really competed with the fabric. Emma and I disagreed on the owl. She liked one with feet and sort of a side view… I liked a front view design. It was her bag… so I did what she wanted (and we are both pleased with the result.)
The bag wasn’t perfectly suited for a school bag however, so I made a few minor modifications. Larissa’s finished bag is 12″ x 12″, not quite wide enough to hold school books. So, I added an extra 2 inches to the width, and an additional 2″ width to the inside and outside pockets. I added two pencil holders to the inside pocket, and because the girls will be toting around books in their bags I used a Pellon Fusible Fleece to give the bag more weight and stability. Some other minor changes was to add a small loop near the side handle because my girls love to hang key chains or small toys from their bag. I also made the strap two colored, but that was because I was a little short on fabric. I had 3 inches to cut the long 45″ strips and I did not want narrow straps! So I used the lining fabric on the reverse, and I love how it looks.
Here’s what you need for this project:
- 3/4 yard of home weight fabrics (54″ wide) for the body
- 3/4 yard of home weight fabrics (54″ wide) for the lining
- Pellon fusible fleece (16″ x 25″ piece)
- a small amount of fabric for decorating plus rick rack, and buttons
- HeatnBond lite for the design
Here are the dimensions of the pieces for the bags I made:
- strap, cut 2- 3″ x 45″ (For Lily and Emma I had to cut the strap down a lot… You customize the length when the bag is nearly done.)
- body and lining, cut 1 each- 16″ x 25″
- Pellon fusible fleece, cut 1 – 16″ x 25″
- flap and flap lining, cut 1 each- 14″ x 13.5″ (I used a cereal bowl to round my corners, Larissa recommends a 6.5″ circle. I placed my fabrics right sides together, traced the rounded edge of the bowl and cut out the rounded corner of both the flap and the lining at the same time.)
- outside pocket, cut 2 – 11″ x 7.5″ (again I cut one from the body fabric and one from the lining fabric)
- inside pocket, cut 2 – 11″ x 5.5″ (ditto)
- key chain loop, cut 1 – 1.5″ x 3″ (press in half, wrong sides together, then press a hem on both sides evenly. Stitch close the the edge)
For the design of the bags I stumbled upon a wonderful template for the squirrels at The Long Thread. The owl was a bit more tricky. I had trouble finding a nice template. With the popularity of owls I was really surprised. I found this one from Martha Stewart. But Emma didn’t love it. I ended up drawing the owl free-hand based off an owl stamp Emma liked… and drawing the branch and leaves as well. (If anyone is interested in the design, I can make a template.)
Start by tracing your design onto the smooth side of a piece of HeatnBond light or Wonder Under. Iron the design to the back of your fabric. Keep in mind that your design will be reversed when you cut it out.
Using good scissors carefully cut around your design.
For the squirrel bag, I used a strip of brown fabric to offset the design. I also used rick rack on the top and bottom of the strip. Here is the technique for sewing on the rick rack.
Line your rick rack along the top edge of your fabric and stitch down the middle of the rick rack. I sew to the right of center, but still in the middle section.
Press the outer edge of the rick rack under. This flips the inside edge to the outside.
Now lay out your design and fuse your design pieces to the front flap. Using a decorative stitch, stitch around your design pieces. I used a machine blanket stitch. You can also blanket stitch by hand. Or use a machine zigzag… whatever you fancy.
For the owl bag, I used buttons for the eyes. You’ll want to finish stitching and embellishing all your design elements before you assemble your bag.
Once you have had fun creating your design… and sweating over it like me… it’s time to assemble your bag. Larissa at mmmcrafts has done an amazing job diagramming each step.
The only major change I made to her instructions (other than the changes to size) was adding the fusible fleece. I did this by fusing the fleece to the liner of my bag after the inside pocket had been added. Then when I was sewing the liner together in step 7, I changed my seem allowance to 3/8″ to give a little extra room with the added padding. I squared the corners according to her instructions, but I had to trim the corner piece off after sewing about a 1/4″ from the seam.
The last small changes I made were adding in the little loop for a keychain (slightly out of focus above,) and sewing two seams in the inside pocket for pencils. I made the pencil holders by measuring in 7/8″ line and stitching along from the outside seam of the pocket. Then I measured one more. Stitch down the line, making sure to back stitch at the top of each seam. You could add a loop with a snap. But for the girls I just added a small loop.
The girls can’t wait to fill the nice big pocket on the outside of the bag.
Emma’s off to school. The girls love their new bags… now I want to make one for me. Wait, wait… did I mention the fabric cost me $4 a bag? Isn’t that the coolest?